Motorola LI2208 Specifiche Pagina 78
- Pagina / 416
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
4 - 16 LI2208 Product Reference Guide
RTS Line State
This parameter sets the idle state of the Serial Host RTS line. Scan a bar code below to select Low RTS or
High RTS line state.
Beep on <BEL>
Point-to-Point Mode Only
When this parameter is enabled, the linear imager issues a beep when a <BEL> character is detected on the
RS-232 serial line. <BEL> is issued to gain a user's attention to an illegal entry or other important event.
*Host: Low RTS
Host: High RTS
NOTE This parameter is not supported in Multipoint-to-Point mode.
Beep On <BEL> Character
(Enable)
*Do Not Beep On <BEL> Character
(Disable)
- PRODUCT REFERENCE 1
- PRODUCT REFERENCE GUIDE 3
- Warranty 4
- Revision History 5
- TABLE OF CONTENTS 7
- Table of Contents vii 9
- Table of Contents ix 11
- Table of Contents xi 13
- ABOUT THIS GUIDE 15
- About This Guide xv 17
- Chapter Descriptions 18
- Notational Conventions 18
- Related Documents 19
- Service Information 19
- CHAPTER 1 GETTING STARTED 21
- Scanner Parts 22
- Configuring the Linear Imager 22
- CHAPTER 2 SCANNING 23
- Table 2-1 24
- SCANNING 2 - 3 25
- Scanning 26
- Hands-Free Scanning 27
- Decode Ranges 28
- CHAPTER 3 USB INTERFACE 29
- Connecting a USB Interface 30
- USB INTERFACE 3 - 3 31
- USB Parameter Defaults 32
- USB INTERFACE 3 - 5 33
- USB Host Parameters 34
- USB Device Type (continued) 35
- *No Delay 37
- USB Ignore Unknown Characters 38
- * Enable Keypad Emulation 39
- * Enable 40
- *Disable Simulated Caps Lock 41
- *No Case Conversion 42
- *Enable USB Static CDC 42
- Optional USB Parameters 43
- * 3 msec 44
- USB INTERFACE 3 - 17 45
- * Disable 46
- Toshiba TEC Host Parameters 47
- * Add Symbol Types 48
- * Add Character Counts 48
- Toshiba TEC Include Header 49
- Toshiba TEC Header Character 50
- USB INTERFACE 3 - 23 51
- * Light LED on Good Decode 51
- Indicate Before Transmission 52
- Indicate After Transmission 52
- ASCII Character Set for USB 53
- Table 3-3 54
- USB INTERFACE 3 - 27 55
- USB INTERFACE 3 - 29 57
- Table 3-4 58
- USB INTERFACE 3 - 31 59
- Table 3-6 60
- Table 3-5 60
- USB INTERFACE 3 - 33 61
- Table 3-8 62
- CHAPTER 4 RS-232 INTERFACE 63
- RS-232 Parameter Defaults 65
- RS-232 Host Parameters 66
- RS-232 INTERFACE 4 - 5 67
- *Standard RS-232 68
- RS-232 Host Types (continued) 69
- *Baud Rate 9600 70
- *1 Stop Bit 71
- *Check For Received Errors 71
- Data Bits (ASCII Format) 72
- Hardware Handshaking 73
- Software Handshaking 75
- ACK/NAK with ENQ 76
- XON/XOFF 76
- *Minimum: 2 sec 77
- *Host: Low RTS 78
- *Minimum: 0 msec 79
- *Normal Operation 80
- RS-232 INTERFACE 4 - 19 81
- Table 4-4 82
- RS-232 INTERFACE 4 - 21 83
- RS-232 INTERFACE 4 - 23 85
- CHAPTER 5 IBM INTERFACE 87
- IBM Parameter Defaults 89
- IBM 468X/469X Host Parameters 90
- Optional IBM Parameters 91
- CHAPTER 6 KEYBOARD WEDGE 93
- INTERFACE 93
- Table 6-1 95
- *IBM AT Notebook 96
- Intra-Keystroke Delay 98
- *Disable Caps Lock On 99
- *Disable Caps Lock Override 100
- *No Convert 100
- *Disable Function Key Mapping 101
- *Disable FN1 Substitution 101
- Send Make and Break 102
- Keyboard Map 103
- Table 6-2 104
- Table 6-3 108
- Table 6-4 109
- Table 6-5 110
- Table 6-6 111
- Table 6-7 113
- MISCELLANEOUS SCANNER 115
- Scanning Sequence Examples 116
- Errors While Scanning 116
- User Preferences 118
- Report Version 119
- Parameter Bar Code Scanning 119
- *Beep After Good Decode 120
- *Medium Tone 121
- *High Volume 122
- Beeper Duration 123
- *Standard (Level) 124
- *Enable Hands-Free Mode 125
- *Auto-discriminate 126
- *Pulsing Pattern 127
- * Enable Low Power Mode 128
- Time Delay to Low Power Mode 129
- * 1 Hour 130
- *5 Minutes 131
- Continuous Bar Code Read 133
- Unique Bar Code Reporting 133
- Decode Session Timeout 134
- *Enable Decoding Illumination 135
- Transmit Code ID Character 136
- Prefix/Suffix Values 137
- Scan Data Transmission Format 138
- *Data As Is 139
- FN1 Substitution Values 140
- *Disable No Read 141
- Parameter # F8h 04h 5Eh 142
- Enter Key 143
- (Carriage Return/Line Feed) 143
- CHAPTER 9 SYMBOLOGIES 145
- Symbology Parameter Defaults 146
- SYMBOLOGIES 9 - 3 147
- Table 9-1 148
- SYMBOLOGIES 9 - 5 149
- Disable All Code Types 150
- *Enable UPC-A 151
- *Enable UPC-E 151
- *Disable UPC-E1 152
- *Enable EAN-8/JAN-8 152
- *Enable EAN-13/JAN-13 153
- *Disable Bookland EAN 153
- Parameter # 10h 154
- *Ignore Supplementals 155
- SYMBOLOGIES 9 - 13 157
- Parameter # 50h 157
- *Combined 158
- *Transmit UPC-A Check Digit 159
- *Transmit UPC-E Check Digit 159
- *Transmit UPC-E1 Check Digit 160
- UPC-A Preamble 161
- UPC-E Preamble 162
- UPC-E1 Preamble 163
- Convert UPC-E to UPC-A 164
- Convert UPC-E1 to UPC-A 164
- *Disable EAN/JAN Zero Extend 165
- *Bookland ISBN-10 165
- *New Coupon Format 166
- *Disable ISSN EAN 167
- Code 128 168
- *Code 128 - Any Length 169
- *Enable GS1-128 170
- *Enable ISBT 128 170
- ISBT Concatenation 171
- *Enable Check ISBT Table 172
- *Code 128 Security Level 1 173
- *Enable Code 39 174
- *Disable Trioptic Code 39 174
- *Disable Code 32 Prefix 175
- * Code 39 - Any Length 176
- *Disable Code 39 Check Digit 177
- *Disable Code 39 Full ASCII 178
- Buffer Data 179
- Clear Transmission Buffer 179
- Transmit Buffer 180
- Code 39 Security Level 181
- * Enable Code 93 182
- * Code 93 - Any Length 183
- *Disable Code 11 184
- SYMBOLOGIES 9 - 41 185
- *Disable 186
- Transmit Code 11 Check Digits 187
- Interleaved 2 of 5 (ITF) 188
- SYMBOLOGIES 9 - 45 189
- Convert I 2 of 5 to EAN-13 191
- *I 2 of 5 Security Level 1 192
- Discrete 2 of 5 (DTF) 193
- *D 2 of 5 - Any Length 194
- Codabar (NW - 7) 195
- Codabar - One Discrete Length 196
- (4 to 60) 196
- Codabar - Any Length 196
- *Disable CLSI Editing 197
- *Disable NOTIS Editing 197
- *Upper Case 198
- *Disable MSI 199
- * MSI - Length Within Range 200
- *One MSI Check Digit 201
- *MOD 10/MOD 10 202
- Chinese 2 of 5 203
- Matrix 2 of 5 204
- SYMBOLOGIES 9 - 61 205
- Matrix 2 of 5 Check Digit 206
- Korean 3 of 5 207
- Inverse 1D 208
- GS1 DataBar 209
- *Enable GS1 DataBar Expanded 210
- SYMBOLOGIES 9 - 67 211
- Parameter # F0h, 8Dh 212
- Redundancy Level 1 213
- Redundancy Level 2 213
- Redundancy Level 3 213
- Redundancy Level 4 213
- *Redundancy Level 1 214
- SYMBOLOGIES 9 - 71 215
- Parameter # 4Dh 215
- *Normal Intercharacter Gaps 216
- CHAPTER 10 123SCAN2 217
- Requirements 218
- CHAPTER 11 ADVANCED DATA 219
- FORMATTING 219
- Using ADF Bar Codes 220
- ADF Bar Code Menu Example 220
- Rule 2: The UPC Scanning Rule 221
- Alternate Rule Sets 221
- Default Rules 223
- ADF Bar Codes 224
- Table 11-1 225
- Special Commands 226
- Quit Entering Rules 227
- Disable Rule Set 228
- Criteria 229
- Code Types (continued) 230
- Code Lengths 233
- Code Lengths (continued) 234
- Specific String at Start 237
- Specific String Search 238
- Any Message OK 238
- Numeric Keypad 239
- Numeric Keypad (continued) 240
- Rule Belongs To Set 241
- Send Data 242
- Send Data (continued) 243
- Setup Field(s) 245
- Move Cursor 246
- Move Cursor (continued) 247
- Skip Ahead 248
- Skip Back 249
- Skip Ahead (continued) 249
- Skip Back (continued) 250
- Send Preset Value 251
- Remove All Spaces 251
- Crunch All Spaces 251
- Stop Space Removal 251
- Remove Leading Zeros 252
- Stop Zero Removal 252
- Pad Data with Spaces 253
- Pad Data with Zeros 257
- Control Characters 262
- Keyboard Characters 267
- Send ALT Characters 281
- Send Alt 285
- Send Keypad Characters 286
- Send Function Key 291
- Send Function Key (continued) 292
- Turn On/Off Rule Sets 304
- Turn Off Rule Set 1 305
- Turn Off Rule Set 2 305
- Turn Off Rule Set 3 305
- Turn Off Rule Set 4 305
- Alphanumeric Keyboard 306
- CHAPTER 12 MAINTENANCE 321
- TROUBLESHOOTING & 321
- TECHNICAL SPECIFICATIONS 321
- Approved Cleaning Agents 322
- Cleaning the Linear Imager 322
- Health Care Linear Imagers 323
- Troubleshooting 324
- Table 12-1 325
- Technical Specifications 327
- Table 12-2 328
- Signal Descriptions 329
- PARAMETERS 331
- Table A-1 332
- APPENDIX B COUNTRY CODES 339
- *US English (North American) 340
- Country Codes (Continued) 341
- Symbol Code Identifiers 355
- Table C-1 356
- AIM Code Identifiers 357
- ]C1AIMID 358
- PROGRAMMING REFERENCE C - 5 359
- APPENDIX D SAMPLE BAR CODES 361
- Interleaved 2 of 5 362
- APPENDIX E NUMERIC BAR CODES 365
- NUMERIC BAR CODES E - 3 367
- ALPHANUMERIC BAR CODES F - 3 371
- ALPHANUMERIC BAR CODES F - 5 373
- ALPHANUMERIC BAR CODES F - 7 375
- ALPHANUMERIC BAR CODES F - 9 377
- ALPHANUMERIC BAR CODES F - 11 379
- ALPHANUMERIC BAR CODES F - 13 381
- ALPHANUMERIC BAR CODES F - 15 383
- ALPHANUMERIC BAR CODES F - 17 385
- Table G-1 387
- ASCII CHARACTER SETS G - 3 389
- ASCII CHARACTER SETS G - 5 391
- Table G-2 392
- ASCII CHARACTER SETS G - 7 393
- Table G-4 394
- ASCII CHARACTER SETS G - 9 395
- Table G-7 396
- Table G-6 396
- ASCII CHARACTER SETS G - 11 397
- Numerics 399
- Index - 3 401
- Index - 5 403
- GLOSSARY 405
- Glossary - 3 407
- Glossary - 5 409
- Glossary - 7 411
- Glossary - 9 413
Prodotti e manuali riguardandi Lettori di codici a barre Motorola LI2208
Lettori di codici a barre Motorola DS3508 Specifiche
(386 pagine)
(386 pagine)
Lettori di codici a barre Motorola DS3508 Specifiche
(316 pagine)
(316 pagine)
(2 pagine)
(36 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale